Neilsen Tool Display Rack

Neilsen Tool Display Case

100pc Manifold Stud & Nut Kit
Includes Studs / Copper Flashed Nuts and Brass Nuts
M8 : 1.25 / 35 to 43mm Deep
M10 : 1.5 / 40 to 54mm Deep
Applicable to most modern vehicles.

3pc Ratchet Set : 1/4 | 3/8 | 1/2in.Dr
90 Tooth Mechanism with Quick Release Button

3pc Ratchet Set : 1/4 | 3/8 | 1/2in.Dr
90 Tooth Mechanism with Quick Release Button
and Rubber Grips

3pc Ratchet Set : 1/4 | 3/8 | 1/2in.Dr
90 Tooth Mechanism with Quick Release Button
Curved Handles and Rubber Grips

Digital Display Torque Wrench
10 - 200Nm with 10 Digital Presets.
530mm Long - 1/2in. Drive with 72 Teeth mechanism.
Units : Nm / ft-lb / in-lb / kg-m with 2 percent accuracy.
Auto shut off : 150 seconds with Audible alert mode.
Requires 3 x AAA Batteries / not included.
Ideal for industrial / automotive use.

Digital Display Torque Wrench
17 - 340Nm with 10 Digital Presets.
650mm Long - 1/2in. Drive with 72 Teeth mechanism.
Units : Nm / ft-lb / in-lb / kg-m with 2 percent accuracy.
Auto shut off : 150 seconds with Audible alert mode.
Requires 3 x AAA Batteries / not included.
Ideal for industrial / automotive use.

10in. / 250mm Self-Tightening Adjustable Wrench
Auto adjust no need to reposition.
Tapered Jaw grips even rounded surfaces with precision and control.
Ideal for confined spaces.

8in. Multi-Function VDE Long Nose Pliers
Wire Cutters / Strippers and Crimpers.
Capacity : AWG - 8 / 10 / 12 / 14 / 16 / 18.
Voltage : 1000V
Chrome-Vanadium.

Petrol Injector Remover with Slide Hammer
for BMW N43 | N53 | N54 models
Access directly below injector and held by thumbscrew
Suitable for BMW : 1 | 3 | 5 | 6 | 7 series
Equivalent to : OEM 13 0 180

Valve Keeper Remover and Installer Kit
For most Overhead Valve Engines with valve stems from 4.5 to 7.5mm or 5/16 to 3/8in.
Magnet in tool body captures keepers for quick removal and valve disassembly.
To install keepers - load in retainer on valve stem / then push or tap handle to install.
Push or tap tool with a hammer to remove valve keepers.
Can be used on the car or work bench.
New smaller size works on Toyota four cylinder
and Chrysler New World engine applications.

Ford A/C Compressor Pulley Retaining Tool
3/8in.Dr - Required when changing the A/C pump or pulley.
Applications : Ford vehicles 2010 - 2015
C-Max / B-Max / Ecosport / Edge / Fiesta / Focus
Galaxy / Kuga / S-Max / Transit Courier
OEM : 412-134

Ford A/C Compressor Clutch Pulley Retaining tool.
3/8in.Dr - required when changing the A/C pump or pulley.
Holds the compressor pulley still allowing the fixing bolt to be removed.
Ford vehicles 2010 - 2017
C-Max / Focus / Kuga / Transit Connect / Courier / Ka( / Fiesta.
OEM : 412-154

Ford A/C Compressor Clutch Pulley Retaining tool.
3/8in.Dr - required when changing the A/C pump or pulley
Holds the compressor pulley still allowing the fixing bolt to be removed.
Ford vehicles from 2012 -
Transit and Transit Custom Hybrid PHEV.
OEM : 412-157

Ford A/C Compressor Clutch Pulley Retaining tool.
3/8in.Dr - required when changing the A/C pump or pulley
Holds the compressor pulley still allowing the fixing bolt to be removed.
Ford vehicles from 2008 - 2015
Fiesta / from 2008
B-Max / from 2012
C-Max / from 2010 & 2015
OEM : 412-103

Flat Belt Tension Spanner Set
For BMW / Mini engines EP3 / EP6 / N12 / N14 / N16 and N18 >2007
For releasing the tension when removing and installing the serpentine belt.
Wrench Sizes : 21mm / 30mm with 12-point drive
OEM : 1 116 210

BMW / Mini Timing Chain Kit
For 1.2 / 1.5 / 2.0 / 3.0 Petrol Engines
Applicable to :
1 / 2 / 3 / 4 / 5 / 6 / 7 series
i8 / X1 / X2 / X3 / X4 / Z4
Mini : Clubman / Hatch / Convertible / Countryman.
Engine Codes : B38 - 1.2 / 1.5 | B48 - 2.0 | B58 - 3.0
OEM number : 2 358 122 | 2 357 904 | 2 365 488 | 2 288 380 | 11 4 120.
Suitable for the latest B38 / B48 Mini and B38 / B48 / B58 BMW engines.

BMW / Mini / PSA
Petrol Engine Timing Kit
For 1.6 Turbo Petrol Engines.
Applicable to :
Mini / Clubman / Cooper S - JCW / R55 / 56 / 57
Coupe / Roadster / Countryman / Paceman - JCW / R58 / 59 / 60 / 61.
OEM : 11 9 550 | 11 9 551 | 11 9 552 | 11 9 590

Engine Timing Tool Set
for Fiat / Ford / Citroen / Peugeot
For adjusting the engine timing when renewing the timing belt
or replacing the cylinder head and gasket etc.
Suitable a wide range of models from Citroen / Fiat / Ford and Peugeot

Suitable for Vauxhall / Opel 1.0L / 1.4L Petrol Engines
with Turbocharger and 1.4L Naturally Aspirated Petrol Engines.
Camshaft Alignment Tool for 1.0L / 1.4L Turbo
Camshaft Alignment Plate for 1.4L Non Turbo
Balancer Shaft Alignment Tool
Applicable to : Adam / Astra K / Corsa E - 2014 - 2017

Engine Timing Tool Set
Opel / Vauxhall / Saab and GM 2.0 Petrol Turbo Engines
For twin camshaft 2.0 litre and turbo boost engine chain replacement.
With - Crankshaft Pulley Holding Tool
Inlet Camshaft Alignment Tool
Exhaust Camshaft Alignment Tool
Chain Tensioner Locking Pin

Water Pump Tester Kit
For testing cooling system water pumps in situ while the engine is running.
Indicates the coolant flow by measuring pressure rises
that occur due to the coolant flowing around the block.
Gauge : 0 - 15psi
Rubber Pipe Seals and Blanking Plugs
2 part Pipe Connector Body
2M Nylon Hose and Male Connector

Filter Wrench
for Vauxhall / Opel Vehicles
1/2in.Dr with 15 Grooves / 74.7mm.
For Oil Filters and Oil Filter Housings.
Ideal for positive mounting of the oil filter housing on
Astra K.Insignia B with 1.5 diesel engines
F15DVC | F15DVH with 77KW/90KW

Brake Bleeder Cap - Tesla Model 3 or Y
Made of Aluminium
for power brake bleeding on Tesla Model 3 and Y vehicles.
Adaptor rotates 360 degrees.
Pressure up to 2.5bar / 36psi.
Compatible with most brake pressure bleeding machines or tank pumps.

Brake Bleeder Cap - Tesla Model S or X
Made of Aluminium
for power brake bleeding on Tesla Model 3 and Y vehicles.
Adaptor rotates 360 degrees.
Pressure up to 2.5bar / 36psi.
Compatible with most brake pressure bleeding machines or tank pumps.

Brake Bleeder Cap - Hyundai
90 degrees angled adaptor for restricted areas.
Suitable for Hyundai / Mitsubishi and Nissan.

Professional Brake Line Flaring Tool Kit
For flaring brake pipes and hydraulic tubing.
Can be used on copper / brass / aluminium and steel pipes
For coated and non-coated pipes.
For inside and outside flaring.
Includes 4 pairs of pressure pieces :
4.75mm | 6.35mm | 8mm | 9.5mm
3/16in. | 1/4in. | 5/16in. | 3/8in.

Wheel Hub and Bearing Service Kit
Designed to extract and install the drive flange and wheel bearing
on front and rear wheel drive vehicles where a one piece bearing is used.
Applicable to -
Rear wheel drive vehicles : BMW / Mercedes-Benz and Porsche.
Front wheel drive vehicles : Chrysler / Ford / Honda / Hyundai
Infiniti / Kia / Lexus / Mazda / Nissan / Toyota and VAG.
For use on drive axles only.

Mercedes Headlight Adjusting Wrench
14mm Hex | 3/8in.Dr | Length 195mm.
Ideally suited to areas with very restricted access.
For adjusting the headlights or clearance from bumpers and bonnet on
Audi A7 and Mercedes C-class / W205 - 2014 onwards.

8KW Silent Diesel Generator 3 Phase
Rated / Max. Power : 8KW / 8.5KW
Rated / Voltage : 230V / 400V
Rated Frequency : 50Hz
Rated current : 8.5 / 11.5A
DC Output : 12V / 8.3A
Power Factor : 0.8
Displacement : 667cc
Fuel Tank Capacity : 28L
Rated class : IP23

Multi-Head Hammer
4 In 1 Quick change head hammer
Four interchangeable heads - Plastic and Steel Shock absorbing fibreglass handle with non-slip rubber grip
Suitable for Installation / Furniture and Woodworking projects.

Brick Cutter
This is a Manual Paving Block / Brick Cutter or Splitter
Cutting Length up to 400mm
Cutting Depth : 10 - 100mm

350mm Masonry / Tile Saw Bench
Motor : 230V / 50Hz
Input : 2.2KW
Speed : 2800rpm
Dimensions L x W x H: 1200 x 600 x 1260mm
Table Size : 530 x 430mm
Cutting Disc : 350mm x 25.4mm
Cutting Height : 110mm - 90 degrees / 72mm - 45 degrees
Cutting Length : 700mm
Durable enough to withstand the rigours of daily site use with
a side mounted cutting arm and blade for straight-through cutting

Mitre Spring Pliers & 8 Mitre Clamps with Snap Hook

Mitre Clamp Range : 0 - 50mm
Sharp points pierce the wood for a secure hold ideal for mitred joints.
Allows the mitred corner to be glued for the perfect finish.
Great for picture frames / mouldings / trim work and any compound mitre.

8in. / 200mm Pruning Shears
with Stainless Steel Blades
Aluminium Alloy Handles with Safety Lock
Max. Cutting : 10mm
Ideal for plants and small branches.