Pulley Puller and Installer Set
Removes pressed-on alternator and power steering pulleys
For late model GM / Ford and Chrysler engines
Adapters for Quad 4 engines
Adapters for Ford modular engines

Puller for Ribbed Drive Pulleys
Length - 200mm | Height - 80mm
Low Profile suitable for most vehicles
Knurled Screws - included
Hex Keys

10pc Belt Pulley Puller Set
For removing and installing belt pulleys
power steering pumps / generators and fan wheels etc.
2 cross beams : 140mm and 230mm long
2 pairs of straight pullers : length 60mm and 110mm
1 pair of specifically formed pullers : length 60mm
All pullers and cross beams can be combined
Suitable for pulley diameter up to 200 mm

VAG Cambelt Pulley Holder
For VW 1.4 / 1.6 / 2.0 litre engines
Also for 4 valve engines with pin diameter 11.5 mm
and counter holding the belt pulley of 2 valve engines.
Applicable to : Audi / Skoda / VW vehicles

VW Installation and Tension Lever for ribbed belts
Adjustable automatic belt tension tool with
removable head for maximum flexibility.
Applicable to : VW ASN and BBJ
T4 / Golf / Passat and Polo.

5pc Master Cam Clamp Kit
This universal kit reduces repair time and covers
most Single / Twin and Quad cam engines.
Locks camshafts during belt replacement.
Prevents engine damage due to incorrect timing.
Allows easy operation in small engine bays.

Camshaft Locking Tool
for Audi | Ford | Seat | Skoda | Volkswagen | Volvo
Essential for setting and locking the camshaft
and crankshaft when changing the timing belt.
Includes :
Setting spigot OEM ref.23-047/2064
Setting bracket OEM ref.21-105/2065A

BMW N47 Diesel Crankshaft Locking Tool
For locking the crankshaft in timing position.
Required when replacing one of both timing chains.
Used to measure the amount of chain stretch without dismantling the whole engine.
Applicable to BMW N47 1.6 and 2.0L diesel engines from 2013.

BMW / Mini Camshaft Drive Chain Wear Indicator
For checking the timing chain stretch on BMW Mini petrol engines
without dismantling the engine.
Applicable to Mini Clubman / Club Van / Countryman / Coupe
Paceman and Roadster with 1.4L and 1.6L engines.
Also useful on equivalent PSA engines.
OEM Code : 2353281

BMW Front Crankshaft Timing Case Cover Remover / Installer
For correcting alignment of the front crankshaft timing case cover / at bottom
also helps prevent damage to the new seal during fitting.
Applicable to : BMW 1 | 2 | 3 | 4 Series - X1 | X2
Mini Clubman / Hatch / Countryman.

BMW Front Crankshaft Seal Installer
For removing or installing the front crankshaft oil seal on BMW model engines :
N40 | N42 | N45 | N45T | N46 | N46T | N52 | N53 | N54
BMW model engines.
OEM Codes : 119230 | 119231 | 119233 | 119235 | 2212822

BMW Crankshaft Oil Seal Kit
For removal and installation of the rear crankshaft oil seal.
Applicable to :
N40 | N42 | N45 | N45T | N46 | N46T | N52 | N53 | N54.
OEM Code : 2212827

BMW Crankshaft Seal Tool Set
For removing and installing the front and rear crankshaft seal.
Applicable to :
N20 / N26 / N40 / N42 / N45 / N45T
N46 / N46T / N52 / N53 / N54 / N55
OEM Codes :
110370 | 119181 | 119182 | 119183

Ford Crankshaft Holding Tool
Prevents the crankshaft moving when releasing
or tightening the crankshaft pulley fasteners.
The unique head profile permits access via a deep socket to each of the pulley bolts.
Applicable to : Mondeo and Transit 2.0 / 2.2 / 2.4 / 3.2 litre -
Duratorq Di / TDDi / TDCi Diesel and 2.3 Duratec HE petrol engines.
NOTE : Deep socket is not supplied.
OEM Code : 303-1310

Ford Crankshaft Damper Holding Tool
for 2.0 / 2.3 / 2.5 litre engines
Applicable to : Fusion / Transit Milan / MKZ Escape / Ranger Mariner
plus Hybrid Vehicles.

Crankshaft Pulley Tool
Ford / Volvo 1.8 | 2.0 | 2.3 - 16V Duratec Chain Drive Engines.
For counter holding the crankshaft pulley while
the pulley retaining bolt is loosened or tightened.
Ford : C-MAX | Fiesta | Focus | Galaxy | Mondeo | S-MAX |Transit
Volvo : C30 | S40 | S80 | V50 | V70
OEM Code : 9997218

Crankshaft Pulley Puller
For removing the vibration damper / pulley
installed on Ford 2.0 EcoBlue TDCi engines
when accessing the timing belt.
Applicable to a range of Ford Vehicles.
OEM Codes : 204-158-01 | 205-295
Crankshaft nose protector spigot / puller.

Ford Crankshaft Pulley Removal Tool
for EcoBlue 2.0L Engines.
This tool ensures the vibration damper can be removed without
causing damage to the bonded rubber section of the pulley.
Applicable to : Kuga / Ranger and Transit.
Thrust bolt / external hex drive - 11mm
Thrust spindle / external hex drive - 19mm
OEM Code : 303-1657

Mercedes Crankshaft Oil Seal Installation Kit
Used to install the front and rear crankshaft oil seal.
Applicable to:
M102 | 111 | 112 | 113 | 137 | 156 | 159 | 272 | 275 |
285 | 601 | 602 | 603 | 604 | 605 | 606 | 628 | 629.
OEM Code :119589011400 | 11589084300

Mercedes Crankshaft Oil Seal Installation Kit
Specifically designed to install crankshaft front and rear seals
on Mercedes M651 diesel engines .
OEM Code : 651589006100 | 651589016100

Citroen / Peugeot Petrol Engine Camshaft and Crankshaft Seal Installer Kit
Citroen / Peugeot Petrol 1900-2000

Crankshaft and Camshaft Seal Remover and Installation Kit
Includes 2 Seal removers for multiple applications
Angled blades for removing seals in limited access

Crankshaft Seal Remover / Installer Kit
Seal sizes - 27mm and 58mm in diameter.
Universal covering a wide range of vehicles.
Use the existing bolt in the vehicle for installation.
Screw-type adapter to aid cantering the seal.
With Aluminium Blue Seal Adapters to prevent crank damage.

BMW Crankshaft Pulley Holder
For holding the crankshaft pulley while loosening or tightening
the middle pulley bolt then removing and replacing vibration dampers.
Applicable to : BMW N47 and N57 engines.
Vibration Damper Brace
Holding Sleeve and Screw : M8 for N47 / N57
Holding Sleeve and Screw : M10 for N47TU / N57TU

BMW Mini Crankshaft Turning / Holding Kit
Specially designed to rotate the crankshaft and fix the flywheel.
Crankshaft Pulley Turning Tool
Flywheel Drive Plate Holding Tool
Securing Bolt and Spacer
Flywheel Bolt Socket

BMW Flywheel Locking Tool
for BMW / MINI engines -
N40 to N73 | M47TU | M54 | M57T2/TU | S85 | W17.
With Counter Holder / Spacer Sleeves /
Reduction Sleeve and Mounting Screws.
For locking the flywheel when loosening or
tightening the pulley and the flywheel itself.

BMW Crankshaft Harmonic Balance Tool
for BMW 3 & 5 Series.
Engines : E39 | E46 | E60 | E61 | E81 | E83 | E90 | E91
Holds vibration damper when loosening and tightening centre crankshaft bolt.

Oil Pump / Balance Shaft Alignment Kit
for BMW 1 | 2 | 3 | 4 Series - 6L / 2.0L Petrol Engines.
For fixing the balance shaft and holding the chain sprocket
when used for repairing the chain and sprocket wheel drive.
Applicable to Engine Codes : N20 | N26 2012 - 2017
OEM Codes : 2 212 825 | 2 318 117 | 11 4 120

Balance Shaft Tool Set
For adjusting the balance shaft on the following vehicles :
JLR : ED4 | TD4 | TD4E / 2009 - 2015.
Citroen : C5 | C5 II | C5 III | C6 | C8 | C-Crosse Hdi / 2000 - 2015.
Mitsubishi Outlander : DI-D | DI-OC / 2007 - 2013.
Peugeot : 4007 | 407 | 607 | 807 | 406 | 508 | 607 | Hdi | GT Hdi / 2000 - 2015.
Ford : Galaxy | Mondeo | S-Max | TDCI | TCI / 2018 - 2015.

Harmonic Damper Holding Tool - Honda
1/2in.Dr 50mm offset socket
For maintaining the harmonic damper pulley position
while removing / installing the pulley bolt.
Use with a 1/2in.Dr Ratchet or Power Bar.

JLR Crankshaft Pulley Tool Set
Crankshaft Pulley removal and holding tool
For Jaguar / Land Rover vehicles.
The Crankshaft Pulley needs to be removed for engine servicing.
Applicable to
Jaguar 3.2 | 3.5 | 4.2 V8 engines
Land Rover 4.2 | 4.4 V8 engines
Engine codes: AJ26 | AJ27 | AJ28 | AJ34

JLR Crankshaft Pulley Service Set
For the removal of the front crankshaft pulley / crankshaft vibration damper
fitted to Jaguar / Land Rover 3.0L V6 and 5.0L V8 Petrol Engines.
The crankshaft pulleys are tightened to 200Nm + 270 degrees
so are very tight to undo and must be held by the holding tool in this kit.
Also included in this kit are the components required to remove the pulley safely.
Applicable to : Jaguar / Land Rover and Range Rover Vehicles - 2009 to 2018.

Crankshaft Harmonic Balancer Holding Tool
for Mercedes 1.6 | 1.8 from 2002 to 2018
Designed to securely hold the Harmonic Balancer / crankshaft pulley
while undoing or tightening the crankshaft pulley fixing bolts
in Mercedes 1.6 and 1.8L petrol engines on -
C / CLC / E / CLS / SLK / CLK Class / Sprinter.
OEM Code : 271589004000.

Crankshaft Pulley Retaining Tool
for PSA / Toyota 1.0L | 1.2L Petrol Engines
For holding the front crankshaft pulley mount
while loosening or tightening the central camshaft bolt.
Fits both 3 and 6 bolt fixing pulley hub types.
Applicable to : Citroen / Peugeot / DS / Opel / Vauxhall and Toyota models.
Engine Ref : EB0 1.0L | EB2 1.2L - 3 cylinder wet belted engines.
Use with 1/2in.Dr Power Bar or Ratchet.

Balance Shaft Puller with Slide Hammer
For VAG 1.8L | 2.0L 4 cylinder petrol chain driven injection engines.
Audi - 2007 to 2017
Seat - 2006 to 2017
Skoda - 2007 to 2017
Volkswagen - 2007 to 2017
OEM Code : T10394

Universal Harmonic Balance Puller
Installation and Removal Tool Kit
with Puller Plate and 4 sets of 3 screws
Centre bolt 10mm and 9 adaptors
For use on the crank pulley damper /
crankshaft damper / torsion damper
or vibration damper for drive belts

Harmonic Damper Pulley Puller
for Chrysler / GM / Hyundai and Mazda
3-Jaw Puller with 3 Lengths of Forcing Rods.
Puller separates the harmonic balancer from the crankshaft.
With harmonic balancer holding tool for tightening or loosening
the crankshaft bolt or removing the balancer.

46pc Harmonic Balance Puller Set
Removes Harmonic Balancers / Gear Pulleys
Steering Wheels and Crank Shaft Pulleys
Zinc Plated Yoke and Bolts
5in. Pressure Screw
Small Cantering Adaptor
Large Cantering Adaptor
Flat Shaft Adaptor

VAG Camshaft Pulley Holding Tool Set
For holding the pulleys and sprockets on the
camshaft / crankshaft / oil pump and water pump
while loosening and tightening the fixing bolts.
also suitable for the Common-Rail Diesel Pump-Nozzles
Suitable for Audi | Seat | Skoda | Volkswagen models.

Audi / VW Crankshaft Pulley Holding Tool
For holding the crankshaft pulley when removing or installing the crankshaft central bolt.
AUDI : A3 | A6 | Q5 2004 onwards
VW : TSI / TFSI engines with chain 1.8T | 2.0L 4V
OEM Code : T10355

Porsche Vibration Damper Counter Holder
Vibration damper counter holder for Porsche 970 / 92A
Used to counter hold the crankshaft pulley during removal and installation.
Applicable to : Porsche 4.8L V8 / 2010-2018
OEM Code : 00072196791

VAG Vibration Damper Assembly Tool
Specially designed to fix the timing chain drive sprockets
while installing and removing the vibration damper on
VAG 1.8L / 2.0L TFSi / TSi EA888 engine.
Applicable to Audi / Seat / Skoda / Volkswagen
Vibration damper holding tool.
Crankshaft sprocket holding tool / adapter and nut.

Crankshaft Alignment Tool
1/2in.Drive with 2 gears
Used in conjunction with 1/2in.Dr Ratchet
Allows the engine crankshaft position to be manually rotated.
Applicable to :
MAN 12 cylinder engines and
Mercedes 6 / 8 and 10 cylinder engines.

Ford Camshaft Sprocket Puller
Size 90 x 65mm
Applicable to - F8M | F8Q | S8U | S9U
Also suitable for removing the Impeller.
Also found in Timing Tool Set CT3429

JLR Balance Shaft Service Kit
for Jaguar / Land Rover 2.0L Diesel Engines
Designed for the removal / refitting and setting of the balance shafts
on the Jaguar Land Rover AJ200 2.0L Diesel Engines.
Applicable to:
Jaguar E-Pace / F-Pace / XE / XF
Land Rover Discovery / Sport
Range Rover Evoque / Sport / Velar

4pc Camshaft Adjuster Set
for Mercedes V6 / V8 - M152 / M157 / M276 / M278 Vehicles
Camshaft Position Sensor Reluctor Setting Tools
Used to mark pulse wheel on removed camshaft.
Can be used in conjunction with CT4076
OEM Code : 27

41mm Water Pump Wrench - 1/2in.Dr
For use on older GM - Vauxhall / Opel engines
where the water pump is used to adjust the camshaft belt tension.
Also used on Chevrolet / Daewoo vehicles.
Engines : 1.2 / 1.3 / 1.4 / 1.6V / 1.6D / 1.8
OEM Codes : KM421A | J-42492 | J-42492-A

46mm Water Pump Wrench - 1/2in.Dr
For use on older Vauxhall / Opel engines
where the water pump is used to adjust the camshaft belt tension.
Engines : 1.6 ( 87 ) 1.7D / 1.8 ( 87 ) / 2.0 litre
OEM Code : KM409A

Cam Belt Tensioning Tool
T50 Star Bit - 1/2in.Dr
Allows access to the tensioner adjuster on
Renault K4M / K4J 1.4 and 1.6 petrol engines.
May be used with 1/2in.Dr Adaptor and Ratchet
OEM Code : MOT1368

VAG Crankshaft Turning Adaptor
22mm Square with 12mm Rotating Pivot Pin
Dual Drive : 1/2in.Dr plus 24mm Hex
Used for turning the crankshaft pulley.
Applicable to : 2.4 | 3.2 | 4.2 FSI Engines.
OEM Code : T40058