VAG Crankshaft Seal Flange Remover and Installer
for 1.4 and 1.6 - 16 Valve VAG engines
fitted to Audi / Skoda / Fiat and VW vehicles
Specific tool vital to ensure the correct alignment
of the main seal house crankshaft sensor.
The Seal housing carries the crankshaft sensor mounting.
OEM Code : T10017

VAG Crankshaft Seal Flange Installation Tool
Designed to renew the crankshaft oil seal on Audi / VW vehicles
Applicable to 16V / 20V - 1.9 / 2.0 Diesel Engines since 2006.
For 4 Valve Diesel engines with integrated sender wheel.
Audi A3 4-cyl. VW Golf / Touran
OEM Code : T10134

VAG Crankshaft Oil Seal Tool
Designed for VW 2.5 TDI | 2.5 Blue TDI Engines.
The flywheel end oil seal is integral with the oil seal housing
and speed sender and is supplied with a new timing ring.
If the oil seal is faulty then the whole assembly must be renewed.
Suitable for VW Crafter 2.5L / 2006 - 2013
Engine Codes : BJJ | BJK | BJL | BJM | CEBA | CEBB | CECA | CECB
OEM Code : T50010

VAG Crankshaft Rotation Tool
for VAG 5 Cylinder Engines
Necessary for crankshaft adjustment and as use as a lever.
Suitable for all 5 cylinder VW diesel engines -
VW touareg as of 2003 and transporter as of 2004
Fixing screw allows easy mounting on crankshaft.
OEM Code : T10225

VAG Camshaft Drive Tensioner Wrench
For adjusting the Camshaft drive belt tensioner on
VAG Vehicles with 1.0 / 1.2 / 1.4 turbo charged engines.
Applicable to :
Audi - A1 / A3
Seat - Mii / Leon
Skoda - Octavia / Citigo
Vo

VAG Timing Chain Tension Lever
for 1.8 / 2.0 TFSi Petrol Engines
Allows the timing chain tensioner to be retracted and locked
without removing the lower timing cover.
Applicable to TFSI engines from 2007 onwards
on Audi / Seat / Skoda / Volkswagen models.
OEM Code : T40243

Water Pump Tester Kit
For testing cooling system water pumps in situ while the engine is running.
Indicates the coolant flow by measuring pressure rises
that occur due to the coolant flowing around the block.
Gauge : 0 - 15psi
Rubber Pipe Seals and Blanking Plugs
2 part Pipe Connector Body
2M Nylon Hose and Male Connector

DAF Commercial Vehicle Crankshaft Alignment Tool
This heavy duty tool allows crankshaft rotation via the flywheel.
6 point drive x 24mm x 11 teeth
Applicable to 35T DAF trucks :
65CF | 75CF | 85CF | 95XF | CF75 | CF85
F65 | F75 |

DAF Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : DAF XF105 / Euro5

MAN Engine Crankshaft Alignment Tool
1/2in. Drive
Length : 61mm
Allows the engine crankshaft position to be manually rotated.
Applicable to : MAN engines D20 | D25 | D26 | D28

MAN / Mercedes Crankshaft Alignment Tool
120mm Deep | 1/2in. Drive
Allows the engine crank to be manually adjusted.
Allows pinpoint accuracy calibration.
Adjusting screw in the clutch housing
Triple gear construction
Applicable to :
Mercedes Benz Actros / Atego
MAN 5-/6- and 8-cylinder engines - D25 / 28 etc.

Scania Engine Crankshaft Alignment Tool
1/2in. Drive
For manually rotating the engine crankshaft into position.
Applicable to : Scania Trucks up to 1996
OEM Code : 99309

Volvo Crankshaft Rotating Tool
1/2in.Dr
For rotating the crankshaft on commercial vehicles via flywheel ring gear.
Applicable to : Volvo 6L and 12L.
Engines : D9A | D12 | D16C and FM 360 8x4.
OEM Code : 9996959